Vu+ SOLO Boot Loader Updgrade

nunigaia

Moderator
Thank you Nunigaia

Good day

Altazia

Make attention to the firmware ( image ) you intend to put in your STB ... For SOLO SE V2, the firmware is not " SOLO FIRMWARE ", but " SOLO SE FIRMWARE ", or you can brick your STB.

Have a nice day, too. :)

best regards
nunigaia
 

QASEM125

Vu+ Newbie
Guy i want some help i am upgrade the vu+solo and when he upgrade hes stop on red collor and he didnt show me any picture or voice i need help pls for information my device is chinese made in china he is not a native.
 
Last edited by a moderator:

nunigaia

Moderator
Guy i want some help i am upgrade the vu+solo and when he upgrade hes stop on red collor and he didnt show me any picture or voice i need help pls for information my device is chinese made in china he is not a native.

First of all, next time, don´t write only in " Capital Letters ", because it's hard to read it.

So, you are admiting that you own a clone Vuplus STB, unfortunately we don´t give support for clones.

Please read the forum rules --> http://www.vuplus-community.net/rules.html

" Clones are not welcome here "

" Buy an original Vuplus STB "


best regards
nunigaia
 

Ev0

Admin
Guy i want some help i am upgrade the vu+solo and when he upgrade hes stop on red collor and he didnt show me any picture or voice i need help pls for information my device is chinese made in china he is not a native.
No help, support or discussion about clones is welcome on this board.
 

Meir Kriheli

Vu+ Newbie
I have solo with BH 1.7.8.
I tried putting the files under usb folder: /vuplus/solo/[files]
Nothing happens wit leds.
When I power off and on again, it powers on regularly.
No update is done and not led blinking.
Same for the vu firmware from vuplus web site.
fat32 of course...
What do I miss here?
 

amio76

Vu+ Newbie
Hi

i have trouble with stb vu plus solo HD
i cannot install firmware above 2.1 ( openpli neither black hole)

When i flash with openpli 2.1 , i cannot play any channel as loaded correctly my iptv playlist.

can anyone help me ?
 

nunigaia

Moderator
Hi

i have trouble with stb vu plus solo HD
i cannot install firmware above 2.1 ( openpli neither black hole)

When i flash with openpli 2.1 , i cannot play any channel as loaded correctly my iptv playlist.

can anyone help me ?

Can you please post some photos of your STB?

Like this:

  1. Front
  2. Back
  3. Upper Cover
Thanks, in advance.

best regards
nunigaia
 

amio76

Vu+ Newbie
Can you please post some photos of your STB?

Like this:

  1. Front
  2. Back
  3. Upper Cover
Thanks, in advance.

best regards
nunigaia


Thanks for reply
here some pics
 

Attachments

  • FRONT.jpg
    FRONT.jpg
    178.1 KB · Views: 67
  • REAR ZOOM.jpg
    REAR ZOOM.jpg
    240.5 KB · Views: 64
  • REAR 1.jpg
    REAR 1.jpg
    205.8 KB · Views: 64
  • IMG_20180221_192214.jpg
    IMG_20180221_192214.jpg
    185.9 KB · Views: 63

amio76

Vu+ Newbie
Thanks for reply
here some pics


You may be told me to do that to know if this stb is clone or original , i think original but not sure... i heard that clone do not accept blackhole firmware upper than 2.0....

May you give me solution... i already gived up the fight ... :(
 

nunigaia

Moderator
You may be told me to do that to know if this stb is clone or original , i think original but not sure... i heard that clone do not accept blackhole firmware upper than 2.0....

May you give me solution... i already gived up the fight ... :(

Thanks.

It seems to me that your STB is original.

Flash your STB first with bootloader cfe 2.0 .

Check the first post on this section, you have there the information needed to flash the bootloader. --> http://www.vuplus-community.net/board/threads/vu-solo-boot-loader-updgrade.4358/

Note: Don´t forget to remove all your USB devices attached to your STB, before proceed the flashing procedure. ( this includes: Usb Pen Drives, Usb Tuners, Usb HDD ... etc ).

You can find too the same information howto do it, on official Vuplus Webpage at this link --> http://vuplus.com/board/boardView.php?idx=5&pagenum=2

After flashing the new CFE 2.0 bootloader, try reflash your STB with a new image ( more recent one ):

  • BlackHole 3.0.5A
  • Open BlackHole 4.1.018

best regards
nunigaia
 

amio76

Vu+ Newbie
hy,
i already tried several image (original) , but no success. it seem that the device do not accept firmware over vers 3 ( openpli 3 , bh 3.....) i cannot install fir exemple openpli 4 . openatv 5.1


any idea ?

now i am on openpli 3. cannot upgrade ....
thanks
 
Top