Vu+
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Black Hole Vu+ Duo 2.1.6

Discussion in 'Vu+ Duo Black Hole Images' started by lorenzo64, May 20, 2015.

  1. Shiro

    Shiro BH-C

    Messages:
    1,706
    You cannot mix images versions in Meoboot.
     
  2. ebvhsat

    ebvhsat Vu+ Newbie

    Messages:
    2
    Thank you Team... Still another great job.
    Ben
     
  3. angelofsky1980

    angelofsky1980 BlackHole Driver Specialist

    Messages:
    16,922
    If your box is not genuine... it's normal that your box don't work ... so not bother about these fu***ng "issues" here.
     
  4. Gys

    Gys Vu+ Newbie

    Messages:
    7
    I don't understand, because through meoboot I can chose between flash (= 2.1.3 installed), Meoboot installed 2.1.4 or Meoboot installed 2.1.5 and all three work fine.
    Why does the installed 2.1.6 not boot, Imho I'am not mixing but installing multiboot versions?

    The rear mounted usb works as flash.
     
  5. Steffan

    Steffan Vu+ Newbie

    Messages:
    55
    Like Shiro said; "You must have same version in flash." First download new BH 2.1.6 and run it from flash, then activate Meoboot, then download again BH 2.1.6 and run it from Usb or HDD within Meoboot.
    Like you said, instructions are on the forum....working everytime. Only problem is that you have to be careful which skin to use, not all are working.
     
  6. magsbert

    magsbert Vu+ Newbie

    Messages:
    4
    Man
     
  7. magsbert

    magsbert Vu+ Newbie

    Messages:
    4
    many thanks will down load asap
     
  8. Aluyi

    Aluyi Vu+ Newbie

    Messages:
    13
    Ooh boy that is the bomb, beautiful and well done, you guys are the bomb. Thanks.
     
  9. cdnj

    cdnj Vu+ Newbie

    Messages:
    14
    My box is genuine and has been working perfectly fine for over 16 months until the image update yesterday, now all c lines gone - can only watch freeview, as a friend said, dont try and fix it if not broken!
     
  10. Mito

    Mito Administrator

    Messages:
    6,689
    Read our board rules, no support for illegal stuff here.!
    You are banned for a week!
     
  11. magsbert

    magsbert Vu+ Newbie

    Messages:
    4
    Many thanks a good read,I tend to think like your mate
     
  12. Gys

    Gys Vu+ Newbie

    Messages:
    7
    For further explanation,

    after installing 2.1.3 in flash I extended-flash as per forum instruction. Started meoboot and after that installed version 2.1.4 as well as 2.1.5 in this extended flash, only under meoboot. All three versions boot and run like charme.
    Only this 2.1.6. version doesmn't boot after installinig under meoboot in the extended flash.

    So I doent understand the difference between 2.1.6 and 2.1.4 resp. 2.1.5
     
  13. Gys

    Gys Vu+ Newbie

    Messages:
    7
    Any clue what so ever?
     
  14. Gys

    Gys Vu+ Newbie

    Messages:
    7
    I recalled my previous working methode:

    As my flash is extended in /universe I rebooted through Meoboot into the original in flash installed version, which is 2.1.3
    After that I open meoboot and install the 2.1.6.1 release which takes about 5 minutes. Original config settings are imported during installation.

    The result is that I can now boot through meoboot into version 2.1.6.1 without having to install this version in flash as well as in meoboot and with the possibility to rollback to previous versions. This makes updates very easy and without the risk of a lot of work updating my Vu+ Duo
     
  15. Matrix10

    Matrix10 Administrator

    Messages:
    8,869
    The difference between installed image in flash and one on USB
    with Meoboot is that you continue to use drivers and kernel from image in flash and not from image on USB,Even when you use USB image you using kernel and drivers from flash image.
    So if you have BH 2.1.3 in flash with old drivers and you use BH 2.1.6.1 on USB with new drivers you are not using this new drivers but old ones.

    Open Multiboot is a better choice for Multiboot.
    Each image uses its own drivers and its own kernel.
     
  16. Gys

    Gys Vu+ Newbie

    Messages:
    7
    Thanks for this advice Matrix 10. This explanes things aren't optimal, so I'll try the open multiboot as suggested. Found clear instructions on openpli forum, formating usb, installing open multiboot and then installing new image.
     
    Matrix10 likes this.
  17. mahmudy

    mahmudy Vu+ Newbie

    Messages:
    9
    Thans for BH team this great image 2.1.6. and 2.1.7

    I have a problem after intallation of 2.1.7. My CI modul does not work. İt says in the common interfase menu
    cam loader then no module found.

    Someone help me solving my problem. Thanks,
     
  18. angelofsky1980

    angelofsky1980 BlackHole Driver Specialist

    Messages:
    16,922
    Report it to Vu+ (www.vuplus.com) with all details about your hardware.
     
  19. JayJay

    JayJay Vu+ Newbie

    Messages:
    31
    Hi Everyone i installed 2.1.6 for my genuine vu+ duo but i can not watch my iptv anymore, could you pls advise me what to do?
    Many Thanks
     

Share This Page