CAM Viaccess in VU+ Solo SE

E

essco4355

Vu+ Newbie
It is not working, I don't know why.
The module is recognised, can I see the entitlements. Card is official, no hack. I can see only large macroblocs. If I change in CI menu "High bitrate support" - yes, then only black screen.
If I put the CAM and card in TV then all is ok. Only VU+ not working :(
I tried original firmware from vuplus.com and BH3.
 
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
essco4355 said:
It is not working, I don't know why.
The module is recognised, can I see the entitlements. Card is official, no hack. I can see only large macroblocs. If I change in CI menu "High bitrate support" - yes, then only black screen.
If I put the CAM and card in TV then all is ok. Only VU+ not working :(
I tried original firmware from vuplus.com and BH3.
Click to expand...
If both images (original and BH) have the same issue, you must report the issue to Vu+ (www.vuplus.com) and they should solve the issue in the next driver release.
 
E

essco4355

Vu+ Newbie
Another question: how could I check the status of the card inserted in Smartcard reader slot. Because no card is functioning there: I tried a Connax card and a Viacces card. Black screen. Both cards are NOT paired with receivers or CAM's, and both cards are working well in another CAM's and in another receiver slot reader.
In Common Interface menu I only find CAM's detailes, no card reader.
 
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
essco4355 said:
Another question: how could I check the status of the card inserted in Smartcard reader slot. Because no card is functioning there: I tried a Connax card and a Viacces card. Black screen. Both cards are NOT paired with receivers or CAM's, and both cards are working well in another CAM's and in another receiver slot reader.
In Common Interface menu I only find CAM's detailes, no card reader.
Click to expand...
Card reader is licensed for XCrypt CAS so it's normal that other cards are not detected.
 
J

JBK

Vu+ Newbie
Hi, everybody!I have put the module NTV+ NEOTION SA CAM VIACCESS CI + 1.3.The receiver approximately in an hour of viewing reboots. It is possible to correct it somehow?
 
J

JBK

Vu+ Newbie
Hi, everybody!I have put the module NTV+ NEOTION SA CAM VIACCESS CI + 1.3.The receiver approximately in an hour of viewing reboots. It is possible to correct it somehow?BH 3.02 E
 
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
JBK said:
Hi, everybody!I have put the module NTV+ NEOTION SA CAM VIACCESS CI + 1.3.The receiver approximately in an hour of viewing reboots. It is possible to correct it somehow?BH 3.02 E
Click to expand...
This issue happen with official Vu+ image?
 
AlexWilMac

AlexWilMac

Moderator
Only a reflash is possible.
Before, save your settings (channels) by a specific software (like iDreamX for Mac, Dreamboxedit, for windows or similar).
 
M

Mick12334

Moderator
This thread is for the VU+ Solo SE, a much newer receiver than the VU+ Solo.
If you have a genuine, older, VU+ Solo receiver, then there's little point in updating, to the latest image, as your receiver can't handle a lot of the newer software.
If you still wnat to update, to either the latest Blackhole, or Open Blackhole, make sure you select the correct image, for your receiver.
For the older VU+ Solo:
http://www.vuplus-community.net/board/forums/vu-solo-black-hole-images.32/

Open Blackhole:
http://www.vuplus-community.net/board/forums/openbh-vu-solo-images.118/
 
You must log in or register to reply here.
Top