Vu+
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

vu zero rev2

Discussion in 'Vu+ Imagenes No Oficiales' started by Mike2loco, Jun 19, 2020.

  1. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    Hello friends, I am trying to install the Black Hole 3.0.9.F Vu + Zero & Vu + Zero Rev.2.0 image and I am not getting it, do you know if any new firmware will come out?
     
  2. aitormeteor

    aitormeteor Vu+ Newbie

    Messages:
    4
    no se te instala ?? si no se te instala te pasa lo mismo que ami
     
  3. Mick12334

    Mick12334 Moderator

    Messages:
    2,205
    You can find the image here:
    https://www.vuplus-community.net/board/threads/black-hole-3-0-9-f-vu-zero-vu-zero-rev-2-0.39702/

    Download the image, and unzip it. Load the vuplus folder, onto a FAT 32 formatted USB stick.

    Power off Vu+ Zero using the switch, at the rear of the receiver.
    Insert the USB Pen Drive into the USB socket on the back.
    Switch on Vu+ Zero.

    The white LED, on the left side, of the front panel should begin pulsing, indicating that the image is loading.

    Once the image has successfully loaded, the pulsing will stop and change to blinking on and off.

    When the white LED is blinking, on and off, switch the receiver off, using the switch, at the rear, remove the USB stick, then power it up again.

    At which point are you experiencing a problem?
     
  4. aitormeteor

    aitormeteor Vu+ Newbie

    Messages:
    4
    simplemente ami no me la carga no hace nada , y lo ago tal cual , en formato fat32 , enciendo pero no hace nada del led simple mente se enciende no la carga
     
  5. Mick12334

    Mick12334 Moderator

    Messages:
    2,205
    Try different USB sticks, the cheaper, older, ones, tend to work best.
     
  6. Thomas67

    Thomas67 Vip

    Messages:
    631
    The most common issue when you format an usb stick is that you dont set the "Allocation unit size" to default. But leave it to 4096 bytes
    4096 bytes prepeare the usb stick for Windows, but default just format and does not prepare for any OS. This usally works for flashing.
     
  7. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    I used the same pen for other vu zero rev2 and I didn't have this problem, I already changed the pen and the problem remains
     
  8. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    I have two vu zero rev2 and the only difference between them is the power cable, it’s different
     
  9. Thomas67

    Thomas67 Vip

    Messages:
    631
    Then try and switch power supply even if i dont see any reason it should matter but cant hurt to try
     
  10. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    but it connects with the original software, and the other vu zero cable is no longer the same
     
  11. Thomas67

    Thomas67 Vip

    Messages:
    631
    Now i am a bit confused :) They are identical but the power supply dont fit from one to the other??
    And you can flash Original Software by that you refer to the stock Vu+ image??
     
  12. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    the power cable of the new vu zero ver2 is no longer the same, this is the only difference I see in the two, I can't flash the new one, it connects, but only connects with the original firmware
     
  13. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    the friend aitormeteor says, the same thing happens to me
     
  14. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
  15. Thomas67

    Thomas67 Vip

    Messages:
    631
    Sorry did not read the thread from the start.
    You have one Vu+ Zero and one Vu+ zero ver 2 that explains why there are diffrent power supply.
    But still you can on the new install the Stock Vu+ image but not any other image. ??
    Did you download the image from vuplus.com or have you got it with the new Vu+ zero?

    Also have you try to flash the OpenBlackhole image?
     
  16. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    are the two vu zero rev2, but the power cable is different as you can see in the picture, the first one I bought was six months ago, the one I bought this week is that it comes with a different power cable, but it is a zero vu rev2.
     
  17. Thomas67

    Thomas67 Vip

    Messages:
    631
    Thats strange if they are identical models from Vu+ they should have the same power supply.
    But have you try and flash anyother image then Blackhole? we also have the OpenBlackhole in any case is better suited for your zero
     
  18. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    I've tried different images, it just doesn't do anything, when it turns on it's the original firmware, I think I'll have to wait for a new update
     
  19. Thomas67

    Thomas67 Vip

    Messages:
    631
    Okey then it has not been flashed at all.

    I asume you now how to flash but here is a Youtube video

     
  20. Mike2loco

    Mike2loco Vu+ Newbie

    Messages:
    10
    good morning, I know how to flash, don't you know if any new firmware is coming out for vu zero rev2?
     

Share This Page