aiuto vu-duo mi e rimasto in starting giu
- Thread starter dazio
- Start date
angelofsky1980
BlackHole Driver Specialist
Thread spostato in sezione italiana.
Prova a scollegare le periferiche USB eventualmente collegate....
In ogni caso puoi collegarti al box via telnet e dare qualche comando e riportare qui il risultato... uno che può essere molto utile per capire cosa sta succedendo è il seguente:
Code:
dmesg
dazio
Vu+ Newbie
p provato caricare img me la carica ma poi rimani lo stesso coem prima
nn mi ricordo + come si carica img via serial
ciao
dazio
Vu+ Newbie
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
sata_brcmstb 0000:01:00.0: version 4.0
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:00.0 to 64
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:01:b9:2a)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ata1: SATA link down (SStatus 4 SControl 300)
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Success! Registering the characther device success with 0
blackhole initialised
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
EBI CS0: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000001
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Block size=00020000, erase shift=17
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0
Found NAND on CS0: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d,
tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0xFF for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0xFF for chip on CS0
nand_read_bbt: Bad block at 0x02f20000
nand_read_bbt: Bad block at 0x06de0000
nand_read_bbt: Bad block at 0x077a0000
Creating 7 MTD partitions on "brcmnand.0":
0x000000000000-0x000007600000 : "rootfs"
0x000007600000-0x000007a00000 : "kernel"
0x000007a00000-0x000007c00000 : "boot"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata2: SATA link down (SStatus 4 SControl 300)
UBI: max. sequence number: 0
UBI: volume 0 ("rootfs") re-sized from 799 to 929 LEBs
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 118 MiB
UBI: number of good PEBs: 942
UBI: number of bad PEBs: 2
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 942
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 1223888225
UBIFS: parse sync
UBI: background thread "ubi_bgt0d" started, PID 45
UBIFS: start fixing up free space
UBIFS: free space fixup complete
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 116563968 bytes (113832 KiB, 111 MiB, 918 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
ttyS0: 3 input overrun(s)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 244k freed
NET: Registered protocol family 10
rtw driver version=v3.4.3_4369.20120622
Build at: Aug 29 2012 13:37:38
usbcore: registered new interface driver rtl8192cu
ttyS0: 8 input overrun(s)
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (bm750)
ttyS0: 2 input overrun(s)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
ttyS0: 3 input overrun(s)
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox advanced remote control (native) as /devices/virtual/input/input
0
[LCD]: registered
[CI]:-BM750_PCB_2_1
[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
udevd (98): /proc/98/oom_adj is deprecated, please use /proc/98/oom_score_adj in
stead.
ttyS0: 10 input overrun(s)
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 1 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 5 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ttyS0: 5 input overrun(s)
svc: failed to register lockdv1 RPC service (errno 124).
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 2 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[CI]:ci_dev_open
[CI]:Opening A GPIO's for 7335 platform
[CI]:Opening A GPIO's for 7335 platform....done
[CI]:entering.. A NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card insertion status changed
[CI]:Opening B GPIO's for 7335 platform
[CI]:Opening B GPIO's for 7335 platform....done
[CI]:entering.. B NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card B insertion status changed
[CI]: CI interface initialised
[CI]:ci1_dev_open
[CI]:NEXUS_Remux_Start
[CI]:>>close_mpod tuner:0
[CI]:remux stop
[CI]:get_remux_startcnt() count : 1
[CI]:get_remux_startcnt() count : 1
[CI]:>>close_mpod tuner:1
[CI]:remux stop
[CI]:get_remux_startcnt() count : 0
[CI]:get_remux_startcnt() count : 0
CPU 0 Unable to handle kernel paging request at virtual address 00000028, epc ==
c0976d4c, ra == c0977404
Oops[#1]:
Cpu 0
$ 0 : 00000000 30008700 c0976d4c 00000000
$ 4 : 00000000 30008701 000000b8 00000000
$ 8 : 00000018 802df118 00000000 00000000
$12 : 88c4bc80 7682d9bc 77158f00 0d696910
$16 : 00000002 86ebfe18 00000002 c09773dc
$20 : c0977418 c0977470 00000000 76466b98
$24 : 00000000 c09a0310
$28 : 86ebe000 86ebfde8 012e4710 c0977404
Hi : 00000000
Lo : 00000198
epc : c0976d4c NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
Tainted: P
ra : c0977404 NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
Status: 30008703 KERNEL EXL IE
Cause : 00800008
BadVA : 00000028
PrId : 0002a044 (Brcm4380)
Modules linked in: nfsd exportfs ext2 brcmfb dvb_bcm7335(P) procmk 8192cu ipv6
Process enigma2 (pid: 781, threadinfo=86ebe000, task=86ec3670, tls=77158490)
Stack : 0000000d 86ebfe24 00000000 00000022 00000000 86ebfe18 00000002 c095c024
00000001 88c1cee0 88a32b18 c095b890 00000002 00000001 00000000 00000000
00000000 00000000 00000004 c0d5ecbc 0055dd48 86ebff10 00d99826 005d8c70
00000000 c0959458 00000001 00000068 00000002 8063fb00 86d29380 874d4f40
0055dd48 801210a0 195c0109 0000000b 86eb3010 88c1c260 0055dd48 00000004
...
Call Trace:
[<c0976d4c>] NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
[<c0977404>] NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
[<c095c024>] max9597_enable_output+0x98/0x1fc [dvb_bcm7335]
[<c0959458>] proc_write_color_format+0x10c/0x1a8 [dvb_bcm7335]
[<801210a0>] proc_file_write+0x78/0xc8
[<80119898>] proc_reg_write+0x7c/0xc4
[<800c2f38>] vfs_write+0xc0/0x168
[<800c30ec>] sys_write+0x4c/0xb4
[<8000e9fc>] stack_done+0x20/0x40
Code: 8fb00010 03e00008 27bd0020 <8c850028> 27bdffe8 afb00010 afbf0014 10a0
0007 00808021
---[ end trace 4abe060bd1cbee41 ]---
root@bm750:~#
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
sata_brcmstb 0000:01:00.0: version 4.0
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:00.0 to 64
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:01:b9:2a)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ata1: SATA link down (SStatus 4 SControl 300)
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Success! Registering the characther device success with 0
blackhole initialised
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
EBI CS0: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000001
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Block size=00020000, erase shift=17
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0
Found NAND on CS0: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d,
tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0xFF for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0xFF for chip on CS0
nand_read_bbt: Bad block at 0x02f20000
nand_read_bbt: Bad block at 0x06de0000
nand_read_bbt: Bad block at 0x077a0000
Creating 7 MTD partitions on "brcmnand.0":
0x000000000000-0x000007600000 : "rootfs"
0x000007600000-0x000007a00000 : "kernel"
0x000007a00000-0x000007c00000 : "boot"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata2: SATA link down (SStatus 4 SControl 300)
UBI: max. sequence number: 0
UBI: volume 0 ("rootfs") re-sized from 799 to 929 LEBs
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 118 MiB
UBI: number of good PEBs: 942
UBI: number of bad PEBs: 2
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 942
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 1223888225
UBIFS: parse sync
UBI: background thread "ubi_bgt0d" started, PID 45
UBIFS: start fixing up free space
UBIFS: free space fixup complete
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 116563968 bytes (113832 KiB, 111 MiB, 918 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
ttyS0: 3 input overrun(s)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 244k freed
NET: Registered protocol family 10
rtw driver version=v3.4.3_4369.20120622
Build at: Aug 29 2012 13:37:38
usbcore: registered new interface driver rtl8192cu
ttyS0: 8 input overrun(s)
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (bm750)
ttyS0: 2 input overrun(s)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
ttyS0: 3 input overrun(s)
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox advanced remote control (native) as /devices/virtual/input/input
0
[LCD]: registered
[CI]:-BM750_PCB_2_1
[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
udevd (98): /proc/98/oom_adj is deprecated, please use /proc/98/oom_score_adj in
stead.
ttyS0: 10 input overrun(s)
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 1 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 5 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ttyS0: 5 input overrun(s)
svc: failed to register lockdv1 RPC service (errno 124).
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 2 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[CI]:ci_dev_open
[CI]:Opening A GPIO's for 7335 platform
[CI]:Opening A GPIO's for 7335 platform....done
[CI]:entering.. A NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card insertion status changed
[CI]:Opening B GPIO's for 7335 platform
[CI]:Opening B GPIO's for 7335 platform....done
[CI]:entering.. B NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card B insertion status changed
[CI]: CI interface initialised
[CI]:ci1_dev_open
[CI]:NEXUS_Remux_Start
[CI]:>>close_mpod tuner:0
[CI]:remux stop
[CI]:get_remux_startcnt() count : 1
[CI]:get_remux_startcnt() count : 1
[CI]:>>close_mpod tuner:1
[CI]:remux stop
[CI]:get_remux_startcnt() count : 0
[CI]:get_remux_startcnt() count : 0
CPU 0 Unable to handle kernel paging request at virtual address 00000028, epc ==
c0976d4c, ra == c0977404
Oops[#1]:
Cpu 0
$ 0 : 00000000 30008700 c0976d4c 00000000
$ 4 : 00000000 30008701 000000b8 00000000
$ 8 : 00000018 802df118 00000000 00000000
$12 : 88c4bc80 7682d9bc 77158f00 0d696910
$16 : 00000002 86ebfe18 00000002 c09773dc
$20 : c0977418 c0977470 00000000 76466b98
$24 : 00000000 c09a0310
$28 : 86ebe000 86ebfde8 012e4710 c0977404
Hi : 00000000
Lo : 00000198
epc : c0976d4c NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
Tainted: P
ra : c0977404 NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
Status: 30008703 KERNEL EXL IE
Cause : 00800008
BadVA : 00000028
PrId : 0002a044 (Brcm4380)
Modules linked in: nfsd exportfs ext2 brcmfb dvb_bcm7335(P) procmk 8192cu ipv6
Process enigma2 (pid: 781, threadinfo=86ebe000, task=86ec3670, tls=77158490)
Stack : 0000000d 86ebfe24 00000000 00000022 00000000 86ebfe18 00000002 c095c024
00000001 88c1cee0 88a32b18 c095b890 00000002 00000001 00000000 00000000
00000000 00000000 00000004 c0d5ecbc 0055dd48 86ebff10 00d99826 005d8c70
00000000 c0959458 00000001 00000068 00000002 8063fb00 86d29380 874d4f40
0055dd48 801210a0 195c0109 0000000b 86eb3010 88c1c260 0055dd48 00000004
...
Call Trace:
[<c0976d4c>] NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
[<c0977404>] NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
[<c095c024>] max9597_enable_output+0x98/0x1fc [dvb_bcm7335]
[<c0959458>] proc_write_color_format+0x10c/0x1a8 [dvb_bcm7335]
[<801210a0>] proc_file_write+0x78/0xc8
[<80119898>] proc_reg_write+0x7c/0xc4
[<800c2f38>] vfs_write+0xc0/0x168
[<800c30ec>] sys_write+0x4c/0xb4
[<8000e9fc>] stack_done+0x20/0x40
Code: 8fb00010 03e00008 27bd0020 <8c850028> 27bdffe8 afb00010 afbf0014 10a0
0007 00808021
---[ end trace 4abe060bd1cbee41 ]---
root@bm750:~#
angelofsky1980
BlackHole Driver Specialist
Log molto interessante.
Prova con una immagine NFI presa da http://code.vuplus.com e vedi se le cose cambiano....
dazio
Vu+ Newbie
o provato a caricare img con usb me la carica ma poi rimare lo steso mo nn mi ricordo + coem si fa via serial..
dazio
Vu+ Newbie
20%
dazio
Vu+ Newbie
msgmni has been set to 270
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
sata_brcmstb 0000:01:00.0: version 4.0
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:00.0 to 64
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:01:b9:2a)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
ata1: SATA link down (SStatus 4 SControl 300)
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, major 254
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
EBI CS0: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000001
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Block size=00020000, erase shift=17
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0
Found NAND on CS0: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d,
tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0xFF for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0xFF for chip on CS0
nand_read_bbt: Bad block at 0x02f20000
nand_read_bbt: Bad block at 0x06de0000
nand_read_bbt: Bad block at 0x077a0000
Creating 7 MTD partitions on "brcmnand.0":
0x000000000000-0x000007600000 : "rootfs"
0x000007600000-0x000007a00000 : "kernel"
0x000007a00000-0x000007c00000 : "boot"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata2: SATA link down (SStatus 4 SControl 300)
UBI: max. sequence number: 0
UBI: volume 0 ("rootfs") re-sized from 569 to 929 LEBs
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 118 MiB
UBI: number of good PEBs: 942
UBI: number of bad PEBs: 2
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 942
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 407844564
UBI: background thread "ubi_bgt0d" started, PID 44
UBIFS: parse sync
UBIFS: start fixing up free space
UBIFS: free space fixup complete
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 116563968 bytes (113832 KiB, 111 MiB, 918 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
ttyS0: 2 input overrun(s)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 244k freed
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (bm750)
ttyS0: 1 input overrun(s)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
ttyS0: 3 input overrun(s)
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox advanced remote control (native) as /devices/virtual/input/input
0
[LCD]: registered
[CI]:-BM750_PCB_2_1
[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
udevd (99): /proc/99/oom_adj is deprecated, please use /proc/99/oom_score_adj in
stead.
ttyS0: 9 input overrun(s)
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 1 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
NET: Registered protocol family 10
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
eth0: no IPv6 routers present
[CI]:ci_dev_open
[CI]:Opening A GPIO's for 7335 platform
ttyS0: 6 input overrun(s)
[CI]:Opening A GPIO's for 7335 platform....done
[CI]:entering.. A NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card insertion status changed
[CI]:Opening B GPIO's for 7335 platform
[CI]:Opening B GPIO's for 7335 platform....done
[CI]:entering.. B NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card B insertion status changed
[CI]: CI interface initialised
[CI]:ci1_dev_open
[CI]:NEXUS_Remux_Start
[CI]:>>close_mpod tuner:0
[CI]:remux stop
[CI]:get_remux_startcnt() count : 1
[CI]:get_remux_startcnt() count : 1
[CI]:>>close_mpod tuner:1
[CI]:remux stop
[CI]:get_remux_startcnt() count : 0
[CI]:get_remux_startcnt() count : 0
CPU 0 Unable to handle kernel paging request at virtual address 00000028, epc ==
c0731d4c, ra == c0732404
Oops[#1]:
Cpu 0
$ 0 : 00000000 30008700 c0731d4c 00000000
$ 4 : 00000000 30008701 000000b8 00000000
$ 8 : 00000018 802a1178 00000000 00000000
$12 : 88c4bc80 7708e020 004d0e74 00000001
$16 : 00000002 86c5de18 00000002 c07323dc
$20 : c0732418 c0732470 00000000 76c8a940
$24 : 00000000 c075b310
$28 : 86c5c000 86c5dde8 00f449b8 c0732404
Hi : 00000000
Lo : 00000198
epc : c0731d4c NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
Tainted: P
ra : c0732404 NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
Status: 30008703 KERNEL EXL IE
Cause : 00800008
BadVA : 00000028
PrId : 0002a044 (Brcm4380)
Modules linked in: ipv6 ext2 brcmfb dvb_bcm7335(P) procmk
Process enigma2 (pid: 981, threadinfo=86c5c000, task=88dd7ac8, tls=7798c490)
Stack : 0000000d 86c5de24 00000000 00000022 00000000 86c5de18 00000002 c0717024
00000001 88c1cee0 88a12b18 c0716890 00000002 00000001 00000000 00000000
00000000 00000000 00000004 c0b19cbc 00555ee8 86c5df10 00ba3d66 005cc0e8
00000000 c0714458 00000001 00000068 00000002 8060fb00 88619680 86d51660
00555ee8 80120f40 195c0109 0000000b 887b8010 88c1c260 00555ee8 00000004
...
Call Trace:
[<c0731d4c>] NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
[<c0732404>] NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
[<c0717024>] max9597_enable_output+0x98/0x1fc [dvb_bcm7335]
[<c0714458>] proc_write_color_format+0x10c/0x1a8 [dvb_bcm7335]
[<80120f40>] proc_file_write+0x78/0xc8
[<80119738>] proc_reg_write+0x7c/0xc4
[<800c2f38>] vfs_write+0xc0/0x168
[<800c30ec>] sys_write+0x4c/0xb4
[<8000e9fc>] stack_done+0x20/0x40
Code: 8fb00010 03e00008 27bd0020 <8c850028> 27bdffe8 afb00010 afbf0014 10a0
0007 00808021
---[ end trace 1a1ca72992e1eb9b ]---
ttyS0: 13 input overrun(s)
root@bm750:~#
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
sata_brcmstb 0000:01:00.0: version 4.0
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:00.0 to 64
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:01:b9:2a)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
ata1: SATA link down (SStatus 4 SControl 300)
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, major 254
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
EBI CS0: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000001
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Block size=00020000, erase shift=17
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0
Found NAND on CS0: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d,
tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0xFF for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0xFF for chip on CS0
nand_read_bbt: Bad block at 0x02f20000
nand_read_bbt: Bad block at 0x06de0000
nand_read_bbt: Bad block at 0x077a0000
Creating 7 MTD partitions on "brcmnand.0":
0x000000000000-0x000007600000 : "rootfs"
0x000007600000-0x000007a00000 : "kernel"
0x000007a00000-0x000007c00000 : "boot"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata2: SATA link down (SStatus 4 SControl 300)
UBI: max. sequence number: 0
UBI: volume 0 ("rootfs") re-sized from 569 to 929 LEBs
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 118 MiB
UBI: number of good PEBs: 942
UBI: number of bad PEBs: 2
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 942
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 407844564
UBI: background thread "ubi_bgt0d" started, PID 44
UBIFS: parse sync
UBIFS: start fixing up free space
UBIFS: free space fixup complete
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 116563968 bytes (113832 KiB, 111 MiB, 918 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
ttyS0: 2 input overrun(s)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 244k freed
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (bm750)
ttyS0: 1 input overrun(s)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
ttyS0: 3 input overrun(s)
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox advanced remote control (native) as /devices/virtual/input/input
0
[LCD]: registered
[CI]:-BM750_PCB_2_1
[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
udevd (99): /proc/99/oom_adj is deprecated, please use /proc/99/oom_score_adj in
stead.
ttyS0: 9 input overrun(s)
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
ttyS0: 1 input overrun(s)
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
NET: Registered protocol family 10
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
eth0: no IPv6 routers present
[CI]:ci_dev_open
[CI]:Opening A GPIO's for 7335 platform
ttyS0: 6 input overrun(s)
[CI]:Opening A GPIO's for 7335 platform....done
[CI]:entering.. A NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card insertion status changed
[CI]:Opening B GPIO's for 7335 platform
[CI]:Opening B GPIO's for 7335 platform....done
[CI]:entering.. B NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card B insertion status changed
[CI]: CI interface initialised
[CI]:ci1_dev_open
[CI]:NEXUS_Remux_Start
[CI]:>>close_mpod tuner:0
[CI]:remux stop
[CI]:get_remux_startcnt() count : 1
[CI]:get_remux_startcnt() count : 1
[CI]:>>close_mpod tuner:1
[CI]:remux stop
[CI]:get_remux_startcnt() count : 0
[CI]:get_remux_startcnt() count : 0
CPU 0 Unable to handle kernel paging request at virtual address 00000028, epc ==
c0731d4c, ra == c0732404
Oops[#1]:
Cpu 0
$ 0 : 00000000 30008700 c0731d4c 00000000
$ 4 : 00000000 30008701 000000b8 00000000
$ 8 : 00000018 802a1178 00000000 00000000
$12 : 88c4bc80 7708e020 004d0e74 00000001
$16 : 00000002 86c5de18 00000002 c07323dc
$20 : c0732418 c0732470 00000000 76c8a940
$24 : 00000000 c075b310
$28 : 86c5c000 86c5dde8 00f449b8 c0732404
Hi : 00000000
Lo : 00000198
epc : c0731d4c NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
Tainted: P
ra : c0732404 NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
Status: 30008703 KERNEL EXL IE
Cause : 00800008
BadVA : 00000028
PrId : 0002a044 (Brcm4380)
Modules linked in: ipv6 ext2 brcmfb dvb_bcm7335(P) procmk
Process enigma2 (pid: 981, threadinfo=86c5c000, task=88dd7ac8, tls=7798c490)
Stack : 0000000d 86c5de24 00000000 00000022 00000000 86c5de18 00000002 c0717024
00000001 88c1cee0 88a12b18 c0716890 00000002 00000001 00000000 00000000
00000000 00000000 00000004 c0b19cbc 00555ee8 86c5df10 00ba3d66 005cc0e8
00000000 c0714458 00000001 00000068 00000002 8060fb00 88619680 86d51660
00555ee8 80120f40 195c0109 0000000b 887b8010 88c1c260 00555ee8 00000004
...
Call Trace:
[<c0731d4c>] NEXUS_Gpio_Close_impl+0x0/0x88 [dvb_bcm7335]
[<c0732404>] NEXUS_Gpio_Close+0x28/0x3c [dvb_bcm7335]
[<c0717024>] max9597_enable_output+0x98/0x1fc [dvb_bcm7335]
[<c0714458>] proc_write_color_format+0x10c/0x1a8 [dvb_bcm7335]
[<80120f40>] proc_file_write+0x78/0xc8
[<80119738>] proc_reg_write+0x7c/0xc4
[<800c2f38>] vfs_write+0xc0/0x168
[<800c30ec>] sys_write+0x4c/0xb4
[<8000e9fc>] stack_done+0x20/0x40
Code: 8fb00010 03e00008 27bd0020 <8c850028> 27bdffe8 afb00010 afbf0014 10a0
0007 00808021
---[ end trace 1a1ca72992e1eb9b ]---
ttyS0: 13 input overrun(s)
root@bm750:~#
angelofsky1980
BlackHole Driver Specialist
angelofsky1980
BlackHole Driver Specialist
Riesci a entrare perchè si blocca il caricamento della GUI.
Prova con una immagine NFI via seriale... se ancora non va, contatta il rivenditore per la sostituzione.
Domanda: ci sono etichette attaccate sul tuo box?
dazio
Vu+ Newbie
nn rieco a collercarlo via serial mi dice succese port ma poi nn nn riesco acaricar imf nfi trano e sta cosa ki me la vemdo e gia passato la scadenza e poi lo mandato a ca... gia na volta
mi dice fail open -.-
ManoftheWind
Vu+ User
Eh......., allora è un clone.......
dazio
Vu+ Newbie
no no nn e un clone in dendevo altro ke ce nessuna ediketta indevo altro io eoriginale coem lovo
quanto lo preso io mancerano ancora i cloni 
ma nn eke lo settato per la vendolo on e poi o dovuto tolgliere ls corente e poi a fatto sta coas a?
ManoftheWind
Vu+ User
no no nn e un clone in dendevo altro ke ce nessuna ediketta indevo altro io eoriginale coem lovo
Dicevo questo perchè avevi scritto "si" alla domanda di Angelofsky.
dazio
Vu+ Newbie
ke li possiamo fare adesso ke nn va + ? sucirimenti ...
angelofsky1980
BlackHole Driver Specialist
Bene: cosa c'è scritto sulla etichetta in questione?