Sendersuche Multistreamsender habe ich auf Hispasat F:11330

[cali_ch]

Ich habe eine Problem bei der Sendersuche mit meiner VU's (duo4k und zero4k).

Beim Suchen von Multistreamsender habe ich auf Hispasat folgendes Problem.
Sender sind offen , haben keinen Stream ID, jedoch per PLS mode frei empfangbar.
=> https://www.lyngsat.com/muxes/Hispasat-30W-5_Europe_11330-H.html

Meine VU+Zero4k [Vuplus DVB-S NIM(SI2166) (DVB-S2X)] findet beim Scan die Sender.
Doch die VU+duo4k [Vuplus DVB-S NIM(45308X FBC) (DVB-S2X)] findet KEINE der Sender im Transponder. Signal OK. LOCK OK.

Doch KEINE Sender beim suchen...

Hispasat 30W:
<transponder frequency="11330000" symbol_rate="9140000" polarization="0" fec_inner="3" system="1" modulation="2" is_id="0" pls_mode="1" pls_code="174526" />

Problem haben auch andere... Siehe hier
https://forums.openpli.org/topic/74412-hispasat-multistream-issue/

Darf ich Euch bitten die Treiber oder Sendersuche dafür zu überprüfen?
Stehe natürlich zur Unterstützung da, falls ich etwas Testen oder Auskunft geben kann.
Bitte auch um einen kurzen Feedback.

Vielen vielen vielen Dank für die Unterstützung

Viele Grüsse
Carlos

PS: Kann es jemand auch nachvollziehen und bestätigen? Danke Euch!

 

[cali_ch]

Log of the scan process done:

13:42:53.0833 dvb/frontend.cpp:730 openFrontend [eDVBFrontend] m_need_delivery_system_workaround = 0
13:42:53.0833 dvb/frontend.cpp:732 openFrontend [eDVBFrontend] opening frontend 0
13:42:53.0957 dvb/frontend.cpp:3517 setVoltage [eDVBFrontend0] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
13:42:53.1109 dvb/dvb.cpp:2420 getDemux [eDVBChannel] getDemux cap=00
13:42:53.1109 dvb/dvb.cpp:1104 allocateDemux [eDVBResourceManager] allocate demux cap=00
13:42:53.1110 dvb/dvb.cpp:1280 allocateDemux [eDVBResourceManager] allocating demux adapter=0, demux=0, source=0
13:42:53.1110 dvb/demux.cpp:88 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux0
13:42:53.1111 dvb/frontend.cpp:3226 tune tune tuner 0
13:42:53.1111 dvb/sec.cpp:72 canTune [eDVBSatelliteEquipmentControl] direct_connected 1
13:42:53.1112 dvb/sec.cpp:111 canTune [eDVBSatelliteEquipmentControl] canTune 1
13:42:53.1112 dvb/sec.cpp:126 canTune [eDVBSatelliteEquipmentControl] lnb 0 found
13:42:53.1112 dvb/sec.cpp:136 canTune [eDVBSatelliteEquipmentControl] 0 option(s) at position 3300
13:42:53.1112 dvb/sec.cpp:126 canTune [eDVBSatelliteEquipmentControl] lnb 1 found
13:42:53.1112 dvb/sec.cpp:136 canTune [eDVBSatelliteEquipmentControl] 0 option(s) at position 3300
13:42:53.1113 dvb/sec.cpp:126 canTune [eDVBSatelliteEquipmentControl] lnb 2 found
13:42:53.1113 dvb/sec.cpp:136 canTune [eDVBSatelliteEquipmentControl] 0 option(s) at position 3300
13:42:53.1113 dvb/sec.cpp:126 canTune [eDVBSatelliteEquipmentControl] lnb 3 found
13:42:53.1113 dvb/sec.cpp:136 canTune [eDVBSatelliteEquipmentControl] 1 option(s) at position 3300
13:42:53.1113 dvb/sec.cpp:150 canTune [eDVBSatelliteEquipmentControl] sat 3300 found
13:42:53.1113 dvb/sec.cpp:194 canTune ret1 10000
13:42:53.1114 dvb/sec.cpp:240 canTune [eDVBSatelliteEquipmentControl] ret5 10000
13:42:53.1114 dvb/sec.cpp:257 canTune [eDVBSatelliteEquipmentControl] ret 10000, score old 0
13:42:53.1114 dvb/sec.cpp:264 canTune [eDVBSatelliteEquipmentControl] score new 10000
13:42:53.1114 dvb/sec.cpp:279 canTune [eDVBSatelliteEquipmentControl] final score 10002
13:42:53.1114 dvb/sec.cpp:1056 prepare [eDVBSatelliteEquipmentControl] RotorCmd ffffffff, lastRotorCmd ffffffff
13:42:53.1115 dvb/frontend.cpp:3146 prepare_sat [eDVBFrontend0] prepare_sat System 1 Freq 11330000 Pol 0 SR 9140000 INV 2 FEC 3 orbpos 3300 system 1 modulation 2 pilot 2, rolloff 0, is_id 0, pls_mode 1, pls_code 174526, t2mi_plp_id -1 t2mi_pid 4096
13:42:53.1115 dvb/frontend.cpp:3152 prepare_sat tuning to 1580 MHz
13:42:53.1115 dvb/dvb.cpp:1892 frontendStateChanged [eDVBChannel] OURSTATE: tuner 0 tuning
13:42:53.1202 dvb/frontend.cpp:2482 tuneLoopInt [SEC] set static current limiting
13:42:53.1228 dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 0 setVoltage 2
13:42:53.1228 dvb/frontend.cpp:3517 setVoltage [eDVBFrontend0] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 1
13:42:53.1346 dvb/frontend.cpp:2084 tuneLoopInt [eDVBFrontend] [SEC] tuner 0 sleep 200ms
13:42:53.3347 dvb/frontend.cpp:2431 tuneLoopInt [SEC] invalidate current switch params
13:42:53.3787 dvb/frontend.cpp:2141 tuneLoopInt [SEC] tuner 0 sendDiseqc: e00000(DiSEqC reset)
13:42:53.3787 dvb/frontend.cpp:2152 tuneLoopInt [eDVBFrontend] [SEC] diseqc ioctl duration: 43 ms -> extra guard delay 9 ms
13:42:53.3878 dvb/frontend.cpp:2084 tuneLoopInt [eDVBFrontend] [SEC] tuner 0 sleep 50ms
13:42:53.4964 dvb/frontend.cpp:2141 tuneLoopInt [SEC] tuner 0 sendDiseqc: e00003(DiSEqC peripherial power on)
13:42:53.4965 dvb/frontend.cpp:2152 tuneLoopInt [eDVBFrontend] [SEC] diseqc ioctl duration: 44 ms -> extra guard delay 8 ms
13:42:53.5045 dvb/frontend.cpp:2084 tuneLoopInt [eDVBFrontend] [SEC] tuner 0 sleep 150ms
13:42:53.7124 dvb/frontend.cpp:2141 tuneLoopInt [SEC] tuner 0 sendDiseqc: e01038fe
13:42:53.7125 dvb/frontend.cpp:2152 tuneLoopInt [eDVBFrontend] [SEC] diseqc ioctl duration: 57 ms -> extra guard delay 9 ms
13:42:53.7215 dvb/frontend.cpp:2084 tuneLoopInt [eDVBFrontend] [SEC] tuner 0 sleep 100ms
13:42:53.8216 dvb/frontend.cpp:2441 tuneLoopInt [SEC] update current switch params
13:42:53.8217 dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 0 startTuneTimeout 20000
13:42:53.8218 dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 0 setFrontend: events enabled
13:42:53.8218 dvb/frontend.cpp:2668 setFrontend setting frontend 0 events: on
13:42:53.8399 dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (0)fe event: status 0, inversion off, m_tuning 1
13:42:53.8400 dvb/frontend.cpp:2084 tuneLoopInt [eDVBFrontend] [SEC] tuner 0 sleep 500ms
13:42:53.8971 dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (0)fe event: status 7, inversion off, m_tuning 2
13:42:54.0509 dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (0)fe event: status 1f, inversion off, m_tuning 3
13:42:54.0510 dvb/dvb.cpp:1888 frontendStateChanged [eDVBChannel] OURSTATE: tuner 0 ok
13:42:54.0511 dvb/demux.cpp:88 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux0
13:42:54.0512 dvb/demux.cpp:284 start [eDVBSectionReader] DMX_SET_FILTER pid=0
13:42:54.3401 dvb/frontend.cpp:2482 tuneLoopInt [SEC] set dynamic current limiting

• 13:42:58.0521 dvb/scan.cpp:483 PATready [eDVBScan] got pat, err -1

13:42:58.0522 dvb/demux.cpp:88 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux0
13:42:58.0523 dvb/demux.cpp:284 start [eDVBSectionReader] DMX_SET_FILTER pid=17
...
13:43:58.0528 dvb/scan.cpp:456 SDTready [eDVBScan] got sdt -1
13:43:58.0529 dvb/scan.cpp:1066 channelDone [eDVBScan] channel done!
13:43:58.0529 dvb/scan.cpp:1204 channelDone [eDVBScan] the current channel's ID was not corrected - not adding channel.
13:43:58.0529 dvb/scan.cpp:316 nextChannel [eDVBScan] no channels left: 1 scanned, 0 unavailable, 0 database.
13:43:58.3195 dvb/db.cpp:1265 renumberBouquet [eDVBDB] Renumbering...
13:43:58.3210 dvb/db.cpp:796 saveServicelist [eDVBDB] ---- saving lame channel db
13:43:58.3595 dvb/db.cpp:1004 saveServicelist [eDVBDB] saved 319 channels and 4708 services!
13:43:58.5534 components/scan.cpp:34 scanEvent [eComponentScan] scan done!
13:44:01.6717 dvb/frontend.cpp:933 closeFrontend [eDVBFrontend] try to close frontend 0
13:44:01.6835 dvb/frontend.cpp:3517 setVoltage [eDVBFrontend0] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2

 

[cali_ch]

PLEASE...
*@ VU+ Development:*

Bitte Treiber für den Tuner Vuplus DVB-S NIM(45308X FBC) (DVB-S2X) im Zusammenspiel mit der VU+ Duo 4k (...und andere) überprüfen.

Kann ja nicht sein, dass folgende Meldung bei der Sendersuche kommt.

-> dvb/scan.cpp:456 SDTready [eDVBScan] got sdt -1
-> dvb/scan.cpp:483 PATready [eDVBScan] got pat, err -1
-> dvb/scan.cpp:1204 channelDone [eDVBScan] the current channel's ID was not corrected - not adding channel.
-> dvb/scan.cpp:316 nextChannel [eDVBScan] no channels left: 1 scanned, 0 unavailable, 0 database.

...die Zero4k mit dem NIM(SI2166) (DVB-S2X) findet die Sender ohne Weiteres.

Und andere Tuner-Besitzer (Vuplus DVB-S NIM(45308X FBC) (DVB-S2X) haben es auch!

Wieso wird das vorhandene Problem der seit Beginn besteht nichts gemacht?

Danke im Voraus für die Unterstützung!



Gesendet von meinem MAR-LX1A mit Tapatalk

 

[newgolfer]

This is the international section so you MUST write English only.
Try to edit from like this:
<transponder frequency="11330000" symbol_rate="9140000" polarization="0" fec_inner="3" system="1" modulation="2" is_id="0" pls_mode="1" pls_code="174526" />

to so:
is_id="1"

If you then use an Open Pli image, keep following them on their forum because this is the Black Hole forum with assistance to Black Hole images only.
However, I am attaching the satellites.xml file with all the updated multistrem.

 

[cali_ch]

Hi Newgolfer,

You're right. English.
Thank you for the hints, but also with the setting set to one or your XML I get same result with the tuner. You can see I have 'LOCK' on the parameters mentioned. But NO CHANNELS are found.
As said, with the other box (Zero4k) I see these channels. It's not a setting thing. It's a problem with the mentioned tuner, drivers and channelsearch. Image independent.
Again thanks for your time, but it's something we can't get run without a review of drivers for that tuner.

Very unsatisfied about this issue.
Really deceptioned with the NIN(45308X FBC).
Cheaper tuner/boxes as mine do better...



Gesendet von meinem MAR-LX1A mit Tapatalk

 

[cali_ch]

I uploaded a video so we can see what's working or even not.

Reception is OK for that transponders.
BUT on Vu+ DUO4K with Vuplus DVB-S NIM(45308X FBC) (DVB-S2X)
Tuner now is not possible.



Gesendet von meinem MAR-LX1A mit Tapatalk