is the DvbS2 Technisat Skystar Usb HD now working under BH ?

B

BigBoy77

Vu+ Newbie
hi guys

does anyone knows if this unit is working under the latest black hole imag for solo2 ?

linuxtv.org/wiki/index.php/Technisat_SkyStar_USB_HD

greetz
 
Last edited:
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
With BH 2.0.7 it's correctly detected:

Code: 
usb 2-1: new high speed USB device number 3 using ehci-brcm
technisat-usb2: set alternate setting
dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-SkyStar_USB_HD_FW_v17_63.HEX.fw'
usbcore: registered new interface driver dvb_usb_technisat_usb2
usb 2-1: USB disconnect, device number 3
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
==> rtw_ps_cmd  , enqueue CMD
GPIO_IN=08
@@@@- #2  rtw_ps_processor==> rfstate:rf_on
usb 2-1: new high speed USB device number 4 using ehci-brcm
technisat-usb2: set alternate setting
technisat-usb2: firmware version: 17.63
dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Technisat SkyStar USB HD (DVB-S/S2))
dvb-usb: MAC address: 00:08:c9:f0:b3:89
stv6110x_attach: Attaching STV6110x
technisat-usb2: i2c-error: 60 = 7
usb 2-1: DVB: registering adapter 1 frontend 0 (Technisat SkyStar USB HD (DVB-S/S2))...
IR keymap rc-technisat-usb2 not found
Registered IR keymap rc-empty
input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.1/usb2/2-1/bh-rc/rc0/input1
rc0: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.1/usb2/2-1/bh-rc/rc0
dvb-usb: schedule remote query interval to 100 msecs.
dvb-usb: Technisat SkyStar USB HD (DVB-S/S2) successfully initialized and connected.
 
B

BigBoy77

Vu+ Newbie
hi angel

did you use a "normal" out of the box version of 2.0.7 ?

somehow i still got the same error with my installed 2.0.7.1 as before.

greetz
 
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
BigBoy77 said:
hi angel

did you use a "normal" out of the box version of 2.0.7 ?

somehow i still got the same error with my installed 2.0.7.1 as before.

greetz
Click to expand...

I'm using the ATSC BH experimental image BUT the USB DVB drivers are the same between versions.
Into ATSC edition there are some more drivers to support the US TV standard but they are ininfluent for DVB USB devices.
 
B

BigBoy77

Vu+ Newbie
hi angel

maybe its easier for you to offer me the image where you got it working so i can try it out. would save you some time.

i tried the normal atsc version but it does not work .

thx in advance

greetz
 
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
BigBoy77 said:
hi angel

maybe its easier for you to offer me the image where you got it working so i can try it out. would save you some time.

i tried the normal atsc version but it does not work .

thx in advance

greetz
Click to expand...

I'm into my Solo(1) box the ATSC version for development and the device is correctly detected without errors.
What box do you use?
 
angelofsky1980

angelofsky1980

BlackHole Driver Specialist
BigBoy77 said:
hi angel

i am afraid to ask , but does it now works ?

i would be so great to get it working on my image too


greetz
Click to expand...

During last days I've tried the Multistream support but unfortunately doesen't work correctly and the device is not yet detected with driver modification for multistream. ASAP in the next weend probably I'll check with standard BH image
 
You must log in or register to reply here.
Top